Victory RH-2D-7-EW-PT Spécifications télécharger pdf (Page 4)

Proper installation is the first step to operation. We recommend that your warmer/ refrigerator be installed by

an authorized Victory Certified Installer.

Receiving Shipment

All units are performance tested and thoroughly inspected prior to shipment. Upon leaving the factory, all units are in

perfect condition. Upon receipt, examine the exterior of the shipment packaging for any signs of rough handling. If the

cabinet is damaged, it should be noted on the delivery slip or bill of lading and signed. A claim must be filed immediately

against the carrier indicating the extent and estimated cost of damage incurred.

Uncrating

ools Needed : 3/4” Box Wrench

●●

Adjustable Wrench

●●

Level

WARNING: Never lay your warmer / refrigerator down on either its back, front or sides. This allows compressor oil into the

refrigerant lines which can damage the compressor at start-up. If the unit is laid down, it must be set upright for a minimum

of 12 hours before starting the compressor. Failure to adhere to the above recommendation will void the warranty.

1. Split plastic wrap along one of the cardboard posts. Remove and discard all packaging material, tape and interior

components.

2. Move cabinet as close to final location as possible before removing skid.

3. Remove the shipping skid by tipping the cabinet forward. Remove the shipping bolts with 3/4” box wrench while

the cabinet is held in one direction. Repeat this procedure while the cabinet is held in the opposite direction.

4. Use extreme caution when removing the wooden skid, especially when the last bolt is removed. If not properly

blocked, the skid will fall to the floor.

Locating Your New Storage Warmer/ Refrigerator

Consider the following when selecting a location for your warmer/ refrigerator:

1. Clearance - There must be a minimum clearance of 10” between the top of the warmer / refrigerator and the ceiling.

2. Floor Load - The floor on which the cabinet will rest must be free of vibration and suitably strong enough to support

the combined weights of the cabinet plus the maximum product load.

3. Ventilation - The air cooled, self-contained warmer/ refrigerator requires a sufficient amount of cool, clean air. Avoid

placing the refrigerator near heat generating equipment such as ovens, ranges, heaters, fryers, steam kettles, etc., and

out of direct sunlight. Avoid locating the self-contained refrigerator in an unheated room, or where the room

temperature may be below 55°F.

Installing Legs or Casters

Warmer / Refrigerator cabinets are shipped with 1/2” single stud mounted legs or casters.

1. Legs/ Casters must be screwed by hand into the threaded holes located on the case bottom (*Note: Once the caster

cannot be turned, take a 3/4” box wrench and tighten the nut in between the mounting plate and wheel of the caster

until it is snug).

2. Tilt the cabinet in one direction approximately eight inches and block it securely with several pieces of 2 x 4 lumber or

other suitable material.

3. Screw in the two left or right legs/casters.

4. Repeat this procedure to install the other legs/casters.

Leveling

Cabinets must be leveled when installed. Failure to level your cabinet may result in doors not sealing, closing properly or

condensate water not draining properly.

Legs - Rotate the foot of the leg with an adjustable wrench to achieve desired height for leveling.

Casters - Cabinets with casters can be leveled by placing large flat washers in between 1/2” stud and holes located

on the case bottom.

INSTALLATION INSTRUCTIONS

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Victory RH-2D-7-EW-PT Spécifications Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Non Victory RH-2D-7-EW-PT